Influence of Khat Extract (Catha edulis) on corrosion resistance of Co-Cr dental alloys / Influência do extrato de Khat (Catha edulis) na resistência à corrosão de ligas dentais Co-Cr

Objective: The aim of this experimental study was to assess the effect of khat extract with different concentrations on the corrosion resistance of cobalt-chromium (Co-Cr) dental alloys used for removable denture. Material and Methods:The corrosion resistance of three Co-Cr alloys (Neobond II®, Kera 501® and PD Casta H®) was evaluated in artificial saliva in presence of three different concentrations of khat extracts. Fusayama-Meyer artificial saliva was used as a reference solution. The corrosion properties of the alloys were analyzed using potentiodynamic polarization, electrochemical impedance spectroscopy and surface analysis. The data was presented in means, standard deviations, and related figures. Comparison between the different concentrations was done using 1-way ANOVA test. The surface analysis was performed using scanning electron microscopy (SEM). Results: the results showed that the corrosion resistance of the three alloys tested (Neobond II®, Kera 501® and PD Casta H®) decreased in artificial saliva containing khat extract compared with that of the reference solution. Additionally, the corrosion resistance of the three Co-Cr dental alloys decreased by increasing the concentration of khat extract. Furthermore, the results indicate that Neobond II® alloy showed the least corrosion resistance compared with that of Kera 501® and PD Casta H® alloys. Conclusion: Khat extract with different concentrations had negative impact on the corrosion resistance of Cr-Co alloys. More in-vivo studies are highly recommended to confirm the results of the present study (AU)

Objetivo: O objetivo deste estudo experimental foi avaliar o efeito do extrato de khat em diferentes concentrações na resistência à corrosão de ligas dentárias de cobalto-cromo (Co-Cr) utilizadas em próteses removíveis. Material e Métodos:A resistência à corrosão de três ligas de Co-Cr (Neobond II®, Kera 501® e PD Casta H®) foi avaliada em saliva artificial na presença de três concentrações diferentes de extratos khat. A saliva artificial de Fusayama-Meyer foi usada como solução de referência. As propriedades de corrosão das ligas foram analisadas usando polarização potenciodinâmica, espectroscopia de impedância eletroquímica e análise de superfície. Os dados foram apresentados em médias, desvios-padrão e figuras relacionadas. A comparação entre as diferentes concentrações foi feita usando o teste One-way ANOVA. A análise de superfície foi realizada em microscopia eletrônica de varredura (MEV). Resultados: os resultados mostraram que a resistência à corrosão das três ligas testadas (Neobond II®, Kera 501® e PD Casta H®) diminuiu na saliva artificial contendo extrato khat em comparação com a solução de referência. Além disso, a resistência à corrosão das três ligas dentais Co-Cr diminuiu com o aumento da concentração de extrato de khat. Além disso, os resultados indicam que a liga Neobond II® apresentou a menor resistência à corrosão em comparação com as ligas Kera 501® e PD Casta H®. Conclusão: O extrato de Khat com diferentes concentrações teve impacto negativo na resistência à corrosão de ligas de Cr-Co. Mais estudos in vivo são altamente recomendados para confirmar os resultados do presente estudo. (AU)

Resin-dentin bond stability of etch-and-rinse adhesive systems with different concentrations of MMP inhibitor GM1489

Abstract Enzymatic degradation of the hybrid layer can be accelerated by the activation of dentin metalloproteinases (MMP) during the bonding procedure. MMP inhibitors may be used to contain this process. Objective To evaluate the degree of conversion (DC%), dentin bond strength (µTBS) (immediate and after 1 year of storage in water), and nanoleakage of an experimental (EXP) and a commercial (SB) adhesive system, containing different concentrations of the MMP inhibitor GM1489: 0, 1 µM, 5 µM and 10 µM. Methodology DC% was evaluated by FT-IR spectroscopy. Dentin bond strength was evaluated by µTBS test. Half of beams were submitted to the µTBS test after 24 h and the other half, after storage for 1 year. From each tooth and storage time, 2 beams were reserved for nanoleakage testing. Data were analyzed using ANOVA and Tukey's test to compare means (α=0.05). Results All adhesive systems maintained the µTBS after 1 year of storage. Groups with higher concentrations of inhibitor (5 µM and 10 µM) showed higher µTBS values than groups without inhibitor or with 1 µM. The nanoleakage values of all groups showed no increase after 1 year of storage and values were similar for SB and EXP groups, in both storage periods. The inhibitor did not affect the DC% of the EXP groups, but the SB5 and SB10 groups showed higher DC% values than those of SB0 and SB1. Conclusions The incorporation of GM1489 in the adhesive systems had no detrimental effect on DC%. The concentrations of 5 µM GM1489 for SB and 5 µM or 10 µM for EXP provided higher μTBS than groups without GM1489, in the evaluation after 1 year of storage; whereas the concentration of inhibitor did not affect adhesive systems nanoleakage.

Sports supplement induces dental structure corrosion: an in vitro pilot study / El suplemento deportivo induce corrosión en la estructura dental: un estudio piloto in vitro

Dietary supplements are being consumed with an increasingly high frequency among sports practitioners, whether at professional and/or amateur level. The supplements contain some nutritional properties in their composition, so they can dissolute the hydroxyapatite crystals of the enamel and favor the process of dental corrosion. The objective was to measure the corrosive power of protein-based supplementation (Whey Protein), under conditions that resemble the use of the supplement by the athletes, increasing the ecological validity of the study. The teeth of the test group (TG) were placed in contact with the Whey protein solution and then exposed to artificial saliva. And the teeth of the control group (CG) were exposed only to artificial saliva. The analysis occurred in natural healthy molar teeth, so that each tooth of the TG was immersed in 50 mL of supplement for 1.5 minutes and then placed in contact with the artificial saliva for 30 seconds. The same procedure was performed 5 times a day for 30, 60, 90, 120, 150 and 180 days. Each group, in its time (TG0 to TG180), underwent analysis of superficial roughness with the aid of optical profilometer (Talysurf CCI®, 3D model). The control group (CG) did not change its superficial roughness. Half of the teeth of the test group (TG) suffered loss of enamel surface. The values, in micrometers, of surface loss of the TG samples were 1.21; 2.1; 2.0; 1.04; 0.97; 0.8; 0.53; 1.14; 1.9; 2.0; 1.66; 1.80. The dietary supplement (Whey protein®) may be a potential cause of the dental corrosion process, considering the demineralization of hydroxyapatite that occurs along with the surface enamel loss.

Los suplementos dietéticos se consumen con una frecuencia cada vez más alta entre los practicantes de deportes, sea a nivel profesional y / o aficionado. Los suplementos contienen algunas propiedades nutricionales en su composición, por lo que pueden disolver los cristales de hidroxiapatita del esmalte y favorecer el proceso de corrosión dental. El objetivo fue medir el poder corrosivo de la suplementación a base de proteínas (proteína de suero), en condiciones que se asemejan al uso del suplemento por parte de los atletas, aumentando la validez ecológica del estudio. Los dientes del grupo de prueba (TG) se pusieron en contacto con la solución de proteína de suero y luego se expusieron a saliva artificial. Y los dientes del grupo de control (CG) estuvieron expuestos solo a saliva artificial. El análisis se realizó en dientes molares sanos naturales, cada diente del TG se sumergió en 50 ml de suplemento durante 1,5 minutos y luego se puso en contacto con la saliva artificial durante 30 segundos. El mismo procedimiento se realizó 5 veces al día durante 30, 60, 90, 120, 150 y 180 días. Cada grupo, en su momento (TG0 a TG180), se sometió a un análisis de rugosidad superficial con la ayuda de un perfilómetro óptico (Talysurf CCI®, modelo 3D). El grupo de control (CG) no cambió su rugosidad superficial. La mitad de los dientes del grupo de prueba (TG) sufrieron pérdida de la superficie del esmalte. Los valores, en micrómetros, de pérdida de superficie de las muestras de TG fueron 1.21; 2.1; 2,0; 1.04; 0,97; 0.8; 0,53; 1.14; 1.9; 2,0; 1,66; 1.80. El suplemento dietético (Whey protein®) puede ser una causa potencial del proceso de corrosión dental, considerando la desmineralización de la hidroxiapatita que ocurre junto con la pérdida de esmalte superficial.

Comparación in vitro de la resistencia adhesiva de los sistemas adhesivos grabado y enjuague y autograbado / In vitro Comparison of the adhesive strength of the etch and rinse adhesive systems and self etching

Resumen El propósito del estudio fue comparar in vitro la resistencia adhesiva de los sistemas Etch and rinse (grabado y enjuague), 4ta y 5ta generación; y los sistemas Self Etch (autograbado), 6ta y 7ma generación. Se realizó un estudio descriptivo, comparativo. Se utilizaron 20 terceros molares extraídos por motivos ortodóncico y profilácticos. Los cuales fueron cortados por la mitad y se obtuvo 40 muestras, en forma aleatoria los dientes fueron divididos en cuatro grupos, 10 con 4ta generación, 10 con 5ta, 10 con 6ta y 10 con 7ma. Se realizó una prueba de tracción vertical medida en kilogramos fuerza, para luego ser transformados a megapascales (Mpa). Las resinas de 4ta generación obtuvieron una resistencia adhesiva de 29,9 Mpa, las de 5ta una resistencia de 16,9 Mpa, la de 6ta una resistencia de 27,5 Mpa y las de 7ma generación una resistencia de 11,0 Mpa. Los resultados se sometieron a pruebas de normalidad mediante la prueba de Shapiro Wilk, y que fueron analizados mediante el ANOVA de un factor, y se encontró diferencias estadísticamente significativas entre los cuatro grupos de estudio con un valor p de 0,001. Se concluye que el sistema adhesivo de 4ta generación clasificado como Etch and Rinse presentó mejor resistencia adhesiva, seguido del adhesivo de 6ta generación clasificado como Self Etch.

Abstract The purpose of the study was to compare in vitro the adhesive strength of the Etch and Rinse systems of the 4th and 5th generation; and Self Etch systems of the 6th and 7th generation. A descriptive, comparative study was carried out. Twenty third molars were used for this study, (these molars were extracted for orthodontic and prophylactic purposes). Each teeth were cut into two pieces obtaining 40 pieces in total, then they were chosen randomly of which 10 pieces were cut with the 4th generation adhesive strength, 10 with the 5th generation, 10with the 6th generation and 10th with the 7th generation of the adhesive. A vertical traction test was performed, measured in kilograms force, and then transformed into megapascals (Mpa). The 4th generation resins obtained an adhesive resistance of 29.9 Mpa, the 5th generation resins obtained a resistance of 16.9 Mpa, the 6th generation obtained a resistance of 27.5 Mpa and the 7th generation obtained a resistance of 11.0 Mpa. The results were subjected to normality tests using the Shapiro Wilk test. These results were analyzed using the oneway ANOVA, finding statistically significant differences between the four study groups with a p-value of 0.001. As a conclusion; the 4th generation adhesive system classified as Etch and Rinse showed better adhesive strength, followed by the 6th generation adhesive system classified as Self Etch .

Nickel and Chromium Ion Levels in Hair and Gingival Crevicular Fluid with the Corrosion of Brackets in Orthodontic Patients: A Longitudinal Study

Objective: To assess the levels of nickel and chromium ions in hair and Gingival Crevicular Fluid (GCF) of orthodontic patients and to evaluate the corrosion of orthodontic bracket surfaces. Material and Methods: Nickel and chromium ion concentrations were measured in hair and GCF of 15 patients (9 females and 6 males, aged 16-28 years old) who had fixed orthodontic treatment using atomic absorption spectroscopy. The samples were taken before treatment (baseline), 4, 8, and 16 months later during treatment. Along with ionic sampling, microscopic sampling was done. One of each patient brackets was removed to get 15 brackets per group. Five brackets were taken randomly from each group to be examined under scanning electron microscope (SEM). Data obtained were analyzed using paired t-tests. Results: After 16 months, compared with the baseline, average hair nickel level changed from 0.125 µg/g to 0.956 µg/g with statistically significant difference (p=0.00); average chromium level changed from 0.090 µg/g to 0.295 µg/g but no significant difference (p>0.05); average GCF nickel level changed from 3.335 µg/g to 10.410 µg/g; average chromium level changed from 1.859 µg/g to 9.818 µg/g. Both of these increases were significant (p=0.000). SEM examinations showed that the corrosion on brackets was seen in the fourth month, and more severely visible after 8 and 16 months of uses. Conclusion: After 16 months of treatment, compared with the baseline, the hair nickel level was increased by 7.7 times; while for chromium was by 3.3 times. Gingival crevicular fluid nickel level was increased by 3.1 times and chromium level was by 5.3 times. The longer time of treatment, the more ions released and the more corrosion of brackets will be.

Corrosion Resistance of Stainless Steel Brackets After Thermal Recycling by Direct Flaming

Objective: To determine and compare the corrosion resistance (based on the release of nickel and chromium in artificial saliva) of various brands of stainless steel brackets after thermal recycling by direct flaming. Material and Methods: This research study employed 40 stainlesssteel maxillary premolar brackets from different brands (Ormco, GAC, Versadent, S-Ortho, and Protect), which were divided into 5 groups consisting of 8 brackets. The nickel and chromium content of the metal brackets were analyzed by inductively coupled plasma mass spectrometry (ICP-MS), conducted before immersion. For the first treatment, each group was immersed in artificial saliva without direct flaming (recycling); for the second treatment, each group was immersed in artificial saliva with direct flaming (recycling) for 30 days in a pH-neutral (pH=7) solution. ICP-MS was employed to analyze the nickel and chromium released in saliva. The mean differences were measured with Wilcoxon, Kruskal Wallis test, and Post-Hoc Mann Whitney test. Differences were considered statistically significant when p-value<0.05. Results: The mean corrosion resistance based on the nickel content released by the new brackets was 99.95%, 99.87%, 87.09%, 90.58%, and 90.26% for groups A, B, C, D, and E, respectively. The mean corrosion resistance based on the nickel content released by the recycled brackets was 99.90%, 99.80%, 98.19%, 89.76%, and 72.82%, respectively. There was a significant difference in corrosion resistance among the 5 groups after recycling by direct flaming and between new and recycled brackets in each group. Conclusion: The corrosion resistance of the brackets in groups A (Ormco), B (GAC), D (S-Ortho), and E (Protect) decreased after thermal recycling by direct flaming. The Ormco brackets had the highest corrosion resistance after thermal recycling by direct faming.

Twenty-four-month clinical performance of different universal adhesives in etch-and-rinse, selective etching and self-etch application modes in NCCL - a randomized controlled clinical trial

Abstract Objective The aim of this randomized, controlled, prospective clinical trial was to evaluate the performances of two different universal adhesives and one etch-rinse adhesive for restoration of non-carious cervical lesions (NCCLs). Material and Methods Twenty patients with at least seven NCCLs were enrolled. Lesions were divided into seven groups according to adhesive systems and application modes: GSE: GLUMA Universal-self-etch, GSL: GLUMA Universal-selective etching, GER: GLUMA Universal-etch-and-rinse, ASE: All-Bond Universal-self-etch, ASL: All-Bond Universal-selective etching, AER: All-Bond Universal-etch-and-rinse, SBE (Control): Single Bond2-etch-and-rinse. A total of 155 NCCLs were restored with a nano hybrid composite (Tetric N-Ceram). Restorations were scored with regard to retention, marginal discoloration, marginal adaptation, recurrent caries and post-operative sensitivity using modified United States Public Health Service (USPHS) criteria after one week, 6, 12 and 24 months. Statistical evaluations were performed using Chi-square tests (p=0.05). Results The recall rate was 81.9% after the 24-month follow-up. The cumulative retention rates for self-etch groups (GSE: 72.2%, ASE:75%) were significantly lower than other experimental groups (GSL: 93.7%, GER: 100%, ASL: 94.1%, AER: 100%, SBE: 100%) at the 24-month follow-up (p<0.05). Regarding marginal adaptation and marginal discoloration, GSE and ASE groups demonstrated more bravo scores after 6 and 12-month observations but differences were not significant (p>0.05). Only one restoration from ASL group demonstrated post-operative sensitivity at 6 and 12-month observations. No secondary caries was observed on the restorations at any recall. At the end of 24-month observations, no significant differences were detected among groups regarding any of the criteria assessed, except retention. Conclusion GLUMA Universal and All-Bond Universal showed better results in etch-and-rinse and selective etching mode compared to the self-etch mode regarding retention. Etch-and-rinse and selective etching application modes of the current universal adhesives tended to provide better clinical outcomes considering the criteria evaluated at the end of 24-month evaluation.

Análise do processo de corrosão na falha clínica de mini-implantes ortodônticos / Analysis of the corrosion process in the clinical failure of orthodontic miniscrew

Introdução: Mini-implantes ortodônticos são dispositivos de ancoragem confeccionados à base de titânio, possuindo uma camada de óxido de titânio, que desempenha função importante na resistência à corrosão. Objetivo: O objetivo deste estudo foi avaliar a resistência à corrosão e a microestrutura superficial de mini-implantes novos, utilizados que foram perdidos precocemente e os que obtiveram sucesso de estabilidade, analisando se o processo de corrosão influencia a falha ou a perda de estabilidade, a fim de se comparar com as principais causas de sucesso e insucesso clínico. Material e método: A amostra foi composta por 3 grupos de 7 mini-implantes divididos da seguinte maneira: Grupo C: mini-implantes na sua forma original, como são recebidos do fabricante (controle); Grupo PE: mini-implantes utilizados em pacientes e que apresentaram perda de estabilidade precoce em até 2 meses (média de 33,5 dias); Grupo E: mini-implantes utilizados em pacientes com sucesso de estabilidade (média de 230 dias). A análise visual da superfície da rosca dos mini-implantes foi feita através de microscópio eletrônico de varredura e todos foram submetidos a ensaio de polarização cíclica potenciodinâmica em potenciostato. Resultado: A microestrutura superficial não foi significativamente alterada pela permanência e perda precoce de estabilidade em seus sítios ósseos. Conclusão: Os dados sugeriram que a corrosão não foi fator associado à falha do dispositivo ou perda de sua estabilidade, sendo outros fatores, como o tipo do mini-implante, o seu comprimento e o local de implantação, considerados mais preponderantes com influência no seu insucesso.

Introduction: Orthodontic miniscrew are titanium-based anchoring devices, having a layer of titanium oxide, which plays an important role in corrosion resistance. Objective: The objective of this study was to evaluate the corrosion resistance and surface microstructure of new miniscrew, those who were used and lost early and those who had achieved stability success, analyzing if the corrosion process influences the failure or the loss of stability of it, in order to compare with the main causes of success and clinical unsuccess. Materials and method: The sample consisted of 3 groups of 7 miniscrews divided as follows: Group C: miniscrews in their original form, as they are received from the manufacturer (control); Group PE: miniscrews used in patients with early loss of stability in up to 2 months (mean of 33.5 days); Group E: miniscrews used in patients with stability success (mean of 230 days). The visual analysis of the screw surface of the miniscrews was done by scanning electron microscope and all were submitted to a cyclic potentiodynamic polarization in potentiostat. Result: The surface microstructure was not significantly altered by the permanence and early loss of stability in its bone sites. Conclusion: The data suggests that corrosion was not a factor associated with device failure or loss of stability, being other factors such as the type of miniscrews, its length and the site of implantation considered to be the most preponderant with influence in its failure.

Tooth surface treatment strategies for adhesive cementation

PURPOSE: The aim of this study was to evaluate the effect of tooth surface pre-treatment steps on shear bond strength, which is essential for understanding the adhesive cementation process. MATERIALS AND METHODS: Shear bond strengths of different cements with various tooth surface treatments (none, etching, priming, or etching and priming) on enamel and dentin of human teeth were measured using the Swiss shear test design. Three adhesives (Permaflo DC, Panavia F 2.0, and Panavia V5) and one self-adhesive cement (Panavia SA plus) were included in this study. The interface of the cement and the tooth surface with the different pre-treatments was analyzed using SEM. pH values of the cements and primers were measured. RESULTS: The highest bond strength values for all cements were achieved with etching and primer on enamel (25.6 ± 5.3 - 32.3 ± 10.4 MPa). On dentin, etching and priming produced the highest bond strength values for all cements (8.6 ± 2.9 - 11.7 ± 3.5 MPa) except for Panavia V5, which achieved significantly higher bond strengths when pre-treated with primer only (15.3 ± 4.1 MPa). Shear bond strength values were correlated with the micro-retentive surface topography of enamel and the tag length on dentin except for Panavia V5, which revealed the highest bond strength with primer application only without etching, resulting in short but sturdy tags. CONCLUSION: The highest bond strength can be achieved for Panavia F 2.0, Permaflo DC, and Panavia SA plus when the tooth substrate is previously etched and the respective primer is applied. The new cement Panavia V5 displayed low technique-sensitivity and attained significantly higher adhesion of all tested cements to dentin when only primer was applied.

Influence of prolonged use of desensitizing dentifrices on dentin bond strength of self-etching adhesive system / Influencia del uso prolongado de pasta dentífrica desensibilizante en la fuerza de unión de la dentina de un sistema adhesivo autocondicionante

Dentin hypersensitivity is a relatively common clinical condition, which affects a large part of the world's population. The objective of this study was to evaluate the influence of previous and prolonged treatment with desensitizing dentifrices (DD) on bond strength to dentin, promoted by a self-etching adhesive system. Seventy non-carious bovine incisors were used, and divided into five groups (n= 14), according to the desensitizing toothpaste used, such as, G1: distilled water (WATER) (control); G2: Colgate Total 12 (CT12) (control); G3: Colgate Sensitive Pro-Relief (CSPR); G4: Sensodyne Rapid Relief (SRR); G5: Sensodyne Repair & Protect (SRP). Teeth had their buccal surfaces flattened until the exposure of dentin, and fragments of 4x4x2 mm were obtained. Fragments were included in polyvinyl chloride (PVC) cylinders and exposed to 17 % EDTA for 1 min. Subsequently, specimens were submitted to 20 000 cycles of simulated dental toothbrushing. After 24 h in artificial saliva, specimens were hybridized (Clearfil SE Bond ­ Kuraray), as well as resin composite cylinders built on dentin surfaces. Samples were stored in distilled water, at 37 C for 24 h, and the shear bond strength was determined. The highest bond strength (MPa) value was seen in CT12 group (4.39), and the lowest one in CSPR group (3.34). Data were statistically analyzed by 1-way ANOVA (ð= 0.05), and results showed that there were no significant differences (p= 0.5986) considering the DD factor. The predominant fracture pattern was cohesive on dentin. The previous and prolonged use of different DD did not affect dentin bond strength promoted by a self-etching adhesive system.

La hipersensibilidad dentinaria es una condición clínica relativamente común, que afecta a una gran parte de la población mundial. El objetivo fue evaluar la influencia del tratamiento previo y prolongado con dentífricos desensibilizantes (DD) en fuerza de adhesión a la dentina, que promueve un sistema adhesivo de autograbado. Se utilizaron 70 incisivos bovinos no cariados, y se dividieron en cinco grupos (n= 14), de acuerdo con la pasta de dientes desensibilizante utilizada: G1: agua destilada (agua) (control), G2: Colgate Total 12 (CT12) (control), G3: Colgate Sensitive Pro-Alivio (CSPR), G4: Sensodyne Rápido Alivio (SRR) y G5: Sensodyne Repair & Protect (SRP). Los dientes tenían sus superficies bucales aplanadas hasta la exposición de la dentina, y se obtuvieron fragmentos de 4x4x2 mm. Los fragmentos se incluyeron en cilindros de cloruro de polivinilo y se expusieron a 17 % de EDTA durante un 1 min. Después, las muestras se sometieron a 20 000 ciclos de cepillado dental simulado. Después de 24 h en saliva artificial, las muestras se hibridaron (Clearfil SE Bond - Kuraray), y cilindros de resina compuesta fueron construidos sobre superficies de dentina. Las muestras se almacenaron en agua destilada, a 37 °C durante 24 h y luego se determinó la resistencia al cizallamiento. El mayor valor de resistencia a la unión (MPa) se observó en el grupo CT12 (4,39), y el menor en el grupo CSPR (3,34). Los datos fueron analizados estadísticamente mediante ANOVA de un factor 1 (ð= 0,05), y los resultados no mostraron diferencias significativas (p= 0,5986) teniendo en cuenta el factor de los DD. El patrón de fractura predominante sobre la dentina fue el cohesivo. El uso previo y prolongado de diferente DD no afectó resistencia de unión a la dentina promovido por un sistema adhesivo de autograbado.

Cytotoxicity of Universal, Self-Etching and Etch-and-Rinse Adhesive Systems According to the Polymerization Time

This in vitro study evaluated in fibroblast cultures the direct cytotoxicity of universal, self-etching and etch-and-rinse adhesive systems according to the polymerization time. Paper discs were impregnated with adhesives and light-cured (10, 20 or 40 s). The discs were then immersed in culture medium to obtain the eluates for the experimental groups (A1-Single Bond 2; A2-Scotchbond Multi-purpose; A3-Clearfil SE Bond; A4 Scotchbond Universal). As a negative control, paper discs were immersed in culture medium only. After 24 h or 7 days, the eluate obtained was applied on fibroblast culture. Cell viability, cell morphology, membrane damage and the presence of residual monomers were evaluated by MTT assay, SEM, flow cytometry and high-performance liquid chromatography (HPLC), respectively. Data were analyzed by Kruskal-Wallis and Mann-Whitney tests (=0.05). All adhesive systems significantly reduced 33-51% cell metabolism when compared to the negative control, regardless of polymerization time, storage period and adhesive system. Moreover, the adhesives caused intense morphological alterations and cell membrane damage. Toxicity was directly related to the presence of residual monomers in the eluates. Residual monomers and additional components are capable of reducing mitochondrial activity, causing morphological alterations and disruption of the cell membrane in fibroblasts, regardless of the polymerization time. This study highlights that despite the more complex composition of the universal adhesive system, its biological response was not more toxic when compared with other systems, even when the shortest polymerization time was tested in cell culture.

O presente estudo in vitro avaliou a citotoxicidade direta dos sistemas adesivos convencionais, autocondicionantes e universais de acordo com o tempo de polimerização em cultura de fibroblastos. Discos de papel foram impregnados com adesivos e fotoativados (10, 20 e 40 s). Os discos foram posteriormente imersos em meio de cultura para obtenção dos eluatos dos grupos experimentais (A1-Single Bond 2; A2-Scotchbond Multi-purpose; A3-Clearfil SE Bond; A4 Scotchbond Universal). Para o controle negativo, os discos de papel foram imersos somente em meio de cultura. Após 24 h ou 7 dias, o eluato obtido foi aplicado na cultura de fibroblastos. O metabolismo celular, morfologia, dano de membrana e presença de monômeros residuais foram avaliados por teste de MTT, MEV, citometria de fluxo e HPLC, respectivamente. Os dados foram analisados estatisticamente por Kruskal-Wallis e Mann-Whitney. Todos os sistemas adesivos reduziram significativamente o metabolismo celular em 33 a 51% quando comparados ao grupo controle, independente do tempo de polimerização, período de armazenamento e tipo de sistema adesivo. O eluato do adesivos causou ainda intensas alterações morfológicas e danos à membrana celular. A toxicidade foi diretamente relacionada à presença de monômeros residuais nos eluatos experimentais. Monômeros residuais e componentes adicionais dos sistemas adesivos foram capazes de reduzir a atividade mitocondrial, causar alterações morfológicas e danos à membrana citoplasmática de fibroblastos, independente do tempo de polimerização. Esse estudo evidencia que apesar de uma composição mais complexa do sistema adesivo universal, sua resposta biológica não apresentou maior toxicidade quando comparado aos demais sistemas, mesmo no menor tempo de polimerização quando testados em cultura celular.

Microbiota Oral Presente en Pacientes Edentulos / Oral Microbiota in Edentulous Patients

El objetivo fue identificar las condiciones orales de pacientes edentulos que acudieron a rehabilitación a la Clínica de Prótesis Total de la Facultad de Odontología de la Universidad Autónoma del Estado de México. El diseño del estudio fue observacional, descriptivo, transversal y prospectivo con una muestra no probabilística de oportunidad y secuencial para estudiar en 160 pacientes el tipo de flora microbiana, portadores de prótesis orales. Los resultados reportan que el promedio de edad para la mayor población edéntula está entre los 56 y 65 años de edad. En relación a las patologías existentes en boca se encontró que el 80% de la población no presentaba signos o síntomas, del 20% eran sintomáticos, todos asociados a estomatitis subprotésica y en 2 de estos pacientes se diagnosticó síndrome de boca ardiente. En relación a la flora microbiana de la cavidad oral encontramos diversidad de microorganismos como: 17% para la flora cocoide Gram+, 2% para flora bacilar Gram-, 17% de presencia de leucocitos, 18% de bacterias, 18% de células epiteliales, 2% de diplococos, 5% de Staphylococcus, 7% de tétradas, 7% de micrococos, 5% de Streptococcus, 2% de enterobactereceas. No se encontraron Candida albicans ni levaduras. El sexo femenino el que presenta mayor tendencia a padecer edentulismo, a razón demográfica nacional que señala que hay más mujeres que hombres. En el apartado de microflora oral se identificó una gran cantidad de microorganismos abundando la flora bacteriana Gram+, pero se identifican varios organismos anaerobios que convierten la cavidad oral en un medio de cultivo, lo cual deberá correlacionarse con la edad y presencia de enfermedades sistémicas concomitantes, ya que microorganismos como el Staphylococcus y Streptococcus pueden tener una repercusión a nivel sistémico, tal y como se demuestra en la asociación de edentulismo a enfermedades cardiovasculares y metabólicas.

The objective of this research was to identify oral conditions of edentulous patients attending rehabilitation at the Total Prosthetics Clinic, Faculty of Dentistry, University of the State of Mexico. The study design was observational, descriptive, transversal and prospective with a nonrandom sample and sequential opportunity to study in 160 patients the type of microbial flora. The results report that the average age for most edentulous population is between 56 and 65 years of age. Regarding existing in mouth pathologies found that 80% of the population did not present signs or symptoms, in the remaining 20% the symptoms most recognized is the pain with 50%, ulcers in 30% and bleeding and inflammation by 10% respectively, all associated with denture stomatitis as the most frequently reported; burning mouth syndrome was reported in 2 of these patients' oral pathology. Regarding microbial flora of the oral cavity we found a variety of microorganisms which breaks down as follows: 17% for plants coccoid Gram +, 2% for plants bacillary Gram-, 17% of white blood cells, 18% of bacteria, 18% ofepithelial cells, 2% diplococci, 5% Staphylococcus, tetrads 7%, 7% of Micrococci, Streptococcus 5%, 2% Enterobactereceas. No yeast or Candida albicans were found. In conclusion, females are more prone to edentulism, national demographic reason. In the area of oral microflora a lot of abounding bacterial flora Gram + microorganisms identified, but several anaerobic organisms convert the oral cavity in a culture medium are identified, which must be correlated with age, presence of concomitant systemic disease, microorganismios as staphylococcus and streptococcus as can have an impact at the systemic level, as demonstrated by the association of edentulism cardiovascular and metabolic diseases.

Osteoblast integration of dental implant materials after challenge by sub-gingival pathogens: a co-culture study in vitro / 国际口腔科学杂志·英文版

Sub-gingival anaerobic pathogens can colonize an implant surface to compromise osseointegration of dental implants once the soft tissue seal around the neck of an implant is broken. In vitro evaluations of implant materials are usually done in monoculture studies involving either tissue integration or bacterial colonization. Co-culture models, in which tissue cells and bacteria battle simultaneously for estate on an implant surface, have been demonstrated to provide a better in vitro mimic of the clinical situation. Here we aim to compare the surface coverage by U2OS osteoblasts cells prior to and after challenge by two anaerobic sub-gingival pathogens in a co-culture model on differently modified titanium (Ti), titanium-zirconium (TiZr) alloys and zirconia surfaces. Monoculture studies with either U2OS osteoblasts or bacteria were also carried out and indicated significant differences in biofilm formation between the implant materials, but interactions with U2OS osteoblasts were favourable on all materials. Adhering U2OS osteoblasts cells, however, were significantly more displaced from differently modified Ti surfaces by challenging sub-gingival pathogens than from TiZr alloys and zirconia variants. Combined with previous work employing a co-culture model consisting of human gingival fibroblasts and supra-gingival oral bacteria, results point to a different material selection to stimulate the formation of a soft tissue seal as compared to preservation of osseointegration under the unsterile conditions of the oral cavity.

Effect of SiO₂-ZrO₂slurry coating on surface performance of zirconia ceramic / 中华口腔医学杂志

<p><b>OBJECTIVE</b>To evaluate the effect of SiO₂-ZrO₂slurry coating on surface performance of zirconia ceramic.</p><p><b>METHODS</b>Seventy pre-sintered zirconia discs were randomly divided into seven groups with 10 discs per group. Sample discs in each group received one of the following seven different surface treatments, namely, sintered (group AS), sand blasting after sintered (group SB), coated with slurry of mole ratio of SiO₂to ZrO₂2:1 (group 2SiO₂-1ZrO₂), coated with slurry of mole ratio of SiO₂to ZrO₂1:1 (group 1SiO₂-1ZrO₂), coated with slurry of mole ratio of SiO₂to ZrO₂1:2 (group 1SiO₂-2ZrO₂), coated with slurry of mole ratio of SiO₂to ZrO₂1:3 (group 1SiO₂-3ZrO₂), coated with slurry of mole ratio of SiO₂to ZrO₂1:4 (group 1SiO₂-4ZrO₂). Profilometer, X-ray diffractometer (XRD), energy dispersive spectrometer, scanning electron microscopy (SEM) were used to analyze surface performance.</p><p><b>RESULTS</b>The surface roughness of the discs in group AS was lower than those in the other groups [(0.33 ± 0.03) µm] (P < 0.05), there was no statistically significant difference (P > 0.05) among group 2SiO₂-1ZrO₂[(3.85 ± 0.38) µm], group 1SiO₂-1ZrO₂[(3.78 ± 0.56) µm] and group 1SiO₂-2ZrO₂[(4.06 ± 0.48) µm], and no difference (P > 0.05) was observed between group 1SiO₂-3ZrO₂[(1.02 ± 0.09) µm] and group 1SiO₂-4ZrO₂[(1.53 ± 0.23) µm] either. However, surface roughness in all coating groups was higher than those in group SB [(0.86 ± 0.05) µm] (P < 0.05). According to the XRD pattern, group AS and all coating groups consisted of 100% tetragonal airconia and monoclinic zirconia was detected at surface of group SB. Contents of surface silicon of coating groups increased significantly, however, no silicon was detected at sample surface of group AS and group SB. SEM showed that zirconia grains of coating exposed since part of silicon was etched by hydrofluoric acid, a three-dimensional network of intergrain nano-spaces was created.</p><p><b>CONCLUSIONS</b>SiO₂-ZrO₂slurry coating could make surface of zirconia rough and increase Si content without creating monoclinic zirconia.</p>

Comparison of platelet adhesion behavior on pure titanium surfaces modified by different techniques / 中华口腔医学杂志

<p><b>OBJECTIVE</b>To evaluate the platelet adhesion ability on pure titanium surfaces modified with different techniques.</p><p><b>METHODS</b>Pure titanium specimens were treated with 5 different surface modification techniques, including machine polish (MP), dual acid-etch (DAE), sand blast-large grit and acid-etch (SLA), micro-arc oxidation (MAO) and anodized titania nanotube (TNT). The surface topographies of specimens were observed by scanning electron microscopy (SEM). Chemical compositions, surface roughness and static water contact angle of specimens were detected by energy dispersive spectrometer (EDS), laser scanning confocal microscope (LSCM) and contact angle analyzer respectively. Platelets were cultured on specimen surfaces for 30 min. The amount and viability of adhered platelets adhered were evaluated. Platelet distribution and morphology were observed by LSCM and SEM.</p><p><b>RESULTS</b>Surface topographies of the five groups of specimens differed significantly. MP, DAE, SLA and MAO surfaces showed micro-scale topographies, while TNT surfaces showed nano-scale topography with nanotubes at the diameter of (80.46 ± 0.35) nm. The surface roughness of MAO was the highest among the 5 groups. TNT surfaces demonstrated the lowest roughness as well as the lowest static water contact angle as 13.55° ± 0.96°. The amount of platelets adhered on TNT surface was the greatest as (300 729 ± 8 325) platelet/µl and the viability was the highest (A450 value 2.14 ± 0.05). Platelet adhered intensively on TNT surfaces, forming pseudopodia, extending and connecting with each other.</p><p><b>CONCLUSIONS</b>Surface properties of pure titanium affect platelet adhesion ability. Nano-scale topography can greatly improve platelet adhesion. Increased surface roughness and hydrophilicity can improve platelet adhesion ability.</p>

Rol del 10-metacriloxidecilfosfato dihidrogenado en el cambio de paradigma de los sistemas adhesivos integrados en la dentina / The Role of 10-methacryloyloxydecyl dihydrogen phosphate in the paradigm of change to adhesive systems integrated to dentin

La aplicación de adhesivos dentarios autograbantes que contienen 10-metacriloxidecilfosfato dihidrogenado supera la resistencia a la biodegradación de la interfase adhesiva de los sistemas tradicionales de grabado total. El mecanismo de acción se basa en la formación de múltiples nanocapas de calcio unido a 2 moléculas 10-metacriloxidecilfosfato dihidrogenado sobre la dentina; estas múltiples capas de 3,5 nm son las que protegerían las fibras colágenas del fenómeno de hidrólisis. Las nanocapas explicarían su alta estabilidad en el tiempo y la fortaleza de la unión, probadas tanto en estudios clínicos como de laboratorio. La interacción con la hidroxiapatita sucede con ácidos de pH bajos, pero mayores que los tradicionales, por lo que surge la necesidad de recomendar el grabado selectivo previo del esmalte. El uso de metacriloxidecilfosfato dihidrogenado permite el cambio de filosofía adhesiva desde el grabado total a la integración adhesiva de la dentina.

Applying self-etching dental adhesives containing 10-MDP overcomes the resistance to biodegradation of the adhesive interface of traditional total etch. The mechanism of action is based on the formation of multiple nano-layers of calcium and two molecules of 10-MDP on the dentin surface. These multiple layers of 3.5 nm protect the collagen fibers from hydrolysis phenomenon. The nano-layer explains its high stability and bond strength over time, tested both by clinical and laboratory studies. Hydroxyapatite interaction occurs with acids of low pH, but are higher than traditional, thus increasing the need to recommend the previous selective etching of the enamel. The use of MDP allows a change of philosophy from the total-etch adhesive to adhesive integration of the dentin.

Evaluation of shear bond strength with different enamel pretreatments: An in vitro study.

Context: Bonding procedures are time consuming and debonding of brackets is a common problem encountered in orthodontics. Aims: The purpose of this in vitro study was to evaluate the shear bond strength (SBS) with different enamel pretreatment (acid etching, air abrasion, and bur abrasion) to enhance the bonding performance. Subjects and Methods: A total of 60 extracted premolars for orthodontic purposes were randomly assigned to three groups based on conditioning method: Group I ‑ conventional etching with 37% phosphoric acid; Group II ‑ air abrasion with 50 μm aluminum oxide; and Group III ‑ bur abrasion with diamond fissure (#330, MANI, Dia‑Burs, New Jersey, USA). After storing the specimens for 24 h in distilled water at 37°C, SBS was measured with Universal testing machine (Lloyd Universal testing machine‑Model No. L.R 100K, UK). The shear force at a crosshead speed of 1 mm/min was transmitted to brackets. The adhesive remnant index (ARIs) scores were recorded after bracket failure. Statistical Analysis Used: Descriptive statistics, multiple comparisons of the SBS of different groups, were performed by analysis of variance. The Tukey’s test was used to evaluate differences in ARI scores between groups. All statistical evaluations were calculated using the Statistical Package for Social Sciences Windows, release 10.0.0 (SPSS Inc., Chicago, Illinois, USA). Results: The analysis of SBS variance (P < 0.01) and Chi‑square test of ARIs scores (P < 0.01) revealed significant differences among three groups tested. The SBS in Group I (mean: 8.822 ± 0.92 MPa) and Group III (mean: 6.015 ± 0.87 MPa) was significantly higher than Group II (mean: 3.824 ± 0.57 MPa). The ARI was used to evaluate the residual adhesive on the enamel after bracket removal. The Tukey’s test was used to evaluate differences in the ARI scores among the groups. Conclusions: The current findings indicate that enamel surface preparation using bur abrasion results in a significant higher than air abrasion; within the limitations of this study recommend bur abrasion as a viable alternative to acid etching.

[Effect of self-etching and single-bottle bonding systems on shear bond strength of fissure sealant to primary and permanent enamel]

Application of self-etching bonding systems to primary and permanent teeth has increased due to the simplicity of work and fewer steps. This experimental study aimed to compare the effect of conventional acid etching and single-bottle and self-etching bonding systems on shear bond strength [SBS] of light-cured fissure sealant to primary and permanent enamel. In this experimental study, the smoothest unprepared proximal enamel surfaces of 30 primary molars [groups 2, 4 and 6] and 30 permanent premolar teeth [groups 1, 3 and 5] were divided into 6 groups of 10. Groups 1 and 2 [control] were acid-etched and received light-cured fissure sealant [Concise 3M-ESPE]. Groups 3 and 4 [SB] were subjected to acid etching + Single Bondadhesive + fissure sealant. Groups 5 and 6 [PLP] received self-etching bonding system [Prompt L-Pop, 3M, ESPE] + fissure sealant. Specimens were then subjected to 500 thermal cycles with the dwell time of 30 seconds. Shear bond strength was determined using Universal Testing Machine [Zwick, Germany]. Mode of fracture was determined under stereomicroscope and data were analyzed using ANOVA, [between-subjects effect] and LSD. SBS was not significantly different between the control and PLP or SB and PLP groups [P>0.05]. However, the difference in SBS between the control and SB groups was statistically significant [P=0.022]. The SBS in primary teeth was less than in permanent teeth in all groups [P<0.05]. Self-etching bonding system [PLP], similar to conventional acid etching technique, provides adequate bond between the light-cured fissure sealant and unprepared enamel. Application of Single Bond Adhesive effectively increased the fissure sealant bond strength

Degradação e corrosão de bráquetes metálicos / Degradation and corrosion of metal brackets

Este estudo in vitro teve como objetivo analisar, por meio de microscopia ótica, as alterações superficiais de bráquetes metálicos submetidos ao processo de degradação química. Para este estudo foram utilizadas amostras de três diferentes bráquetes metálicos, separados de acordo com a marca (Morelli®, Aditek® e Abzil®) e soluções de imersão (solução salina 0,05%, saliva artificial, Coca-Cola®, suco de tomate e vinho). A superfície dos bráquetes foi avaliada inicialmente através do microscópico ótico e fotografada para avaliação qualitativa. Em seguida, os bráquetes foram imersos nas soluções por 15, 30 e 60 dias e as alterações decorrentes da exposição das amostras às soluções foram analisadas por meio do microscópico ótico em cada período (15, 30 e 60 dias). Os resultados mostraram que o vinho, Coca-Cola, suco de tomate e saliva artificial não causaram alterações na superficial dos bráquetes. Entretanto, a imersão em solução salina causou corrosão na superfície de todas as marcas avaliadas. Concluiu-se que a solução salina foi a única solução capaz de causar danos à superfície dos bráquetes metálicos, não havendo distinção entre as marcas comerciais dos bráquetes.

This in vitro study aimed to analyze, by means of optical microscopy, surface changes on metallic brackets subjected to chemical degradation process. For this study we have used samples from three different metallic brackets separated according to their brand (Morelli, Aditek e Abzil), and dip solutions (saline solution 0.05%, artificial saliva, Coca-Cola, tomato juice and wine). The surface of the brackets was initially evaluated by optical microscope and photographed for qualitative evaluation. Then, the brackets were immersed in the solutions for 15, 30 and 60 days. The changes resulting from exposure to the solutions were analyzed by optical microscope in each period (15, 30 and 60 days). The results showed that wine, Coca-Cola, tomato juice and artificial saliva did not cause changes in the surface of the brackets. However, immersion in saline solution caused corrosion on the surface of all brands studied. It was concluded that the saline solution was the only solution capable of damaging the surface of metal brackets, with no distinction among the tested brands.

Comparative study of the titanium and titanium alloy implant electrolytic etching surface / 华西口腔医学杂志

<p><b>OBJECTIVE</b>This preliminary study aims to investigate the effects of titanium and titanium alloy micro-nano-dimensional topography on the biological behavior of osteoblasts in vitro.</p><p><b>METHODS</b>Electrolytic etching (EE) method was used to produce micro-nano dimensional titanium surfaces. The surfaces were observed to determine their effects on the adhesion, proliferation, cell morphology, and alkaline phosphatase (ALP) activity of osteoblasts.</p><p><b>RESULTS</b>The surfaces of the titanium and titanium alloy groups exhibited higher adhesion and proliferation of osteoblasts than those of the mechanical group. The titanium surface was covered with a group of cells, a large number of filopodia, and functional particles. The ALP activity of the titanium group was significantly higher than that of the titanium alloy and mechanical groups.</p><p><b>CONCLUSION</b>EE method in pure titanium and titanium alloy surfaces result in bowl-like nests and nanostructures of different diameters and depths. The diameters of the pure titanium and titanium alloy surfaces range from 30 to 50 μm and 5 to 8 μm, respectively. The former is more conducive to promote the proliferation and differentiation of cells.</p>